|
|
AFG-3081 |
AFG-3051 |
|
Waveforms |
Sinus, Rechteck, Rampe, Impuls, Rauschen, DC, Sin (x) / x, Exponential Rise, Exponential Fall, Negative Ramp |
|
Arbiträrsignale |
|
ARB-Funktion |
Erbaut im Jahr |
|
Sample Rate |
200 MSa / s |
|
Wiederholungsrate |
100MHz |
|
Waveform Länge |
1M Punkte |
|
Amplitudenauflösung |
16 Bit |
|
Non-Volatile Memory |
Zehn 1M Wellenformen(1) |
|
Benutzer definieren Output-Bereich |
Jeder Abschnitt von 2 bis 1M Punkte |
|
Benutzer definieren Mark Output |
Jeder Abschnitt von 2 bis 1M Punkte |
|
Frequenzgang |
|
Reichweite |
Sinus |
80MHz |
50MHz |
|
Quadrat |
|
Dreieck, Rampe |
1MHz |
|
Auflösung |
1uHz |
|
Genauigkeit |
Stabilität |
± 1 ppm0 bis 50 ¿ |
|
± 0,3 ppm18 bis 28 ¿ |
|
Altern |
± 1 ppm,je 1 Jahr |
|
Toleranz |
¿ 1 UHZ |
|
Output Eigenschaften(2) |
|
|
|
|
Amplitude |
Reichweite |
10 mV bis 10 Vss(in 50O) 20 mVpp bis 20 Vpp(open-circuit)
|
|
Genauigkeit |
± 1% der Einstellung ± 1 mVpp
(bei ¿¿1 kHz,> 10 mVpp) |
|
Auflösung |
0,1 mV oder 4-stellig |
|
Ebenheit |
± 1% (0,1 dB) <10 MHz
± 2% (0,2 dB) 10 MHz bis 50 MHz
± 10% (0,9 dB) 50 MHz bis 70 MHz
± 20% (1,9 dB) 70 MHz bis 80 MHz
(Sinus relativ zu 1 kHz) |
|
Units |
Vpp, Vrms, dBm, |
|
Offset |
Reichweite |
± 5 Vpk ac + dc(in 50O) ± 10Vpk ac + dc(Open Circuit)
|
|
Genauigkeit |
1% der Einstellung + 2 mV + 0,5% der Amplitude |
|
Waveform-Ausgang |
Impedanz |
50O typisch(fixed)
> 10 M (Ausgang abgeschaltet) |
|
Schutz |
Kurzschlussfest
Überlastrelais automatisch deaktiviert Hauptausgang |
|
SYNC-Ausgang |
Ebene |
TTL-kompatibel zu> 1 kOhm |
|
Impedanz |
50O nominal |
|
Sinus Eigenschaften |
|
Harmonic Distortion(5) |
-60 DBc DC ~ 1 MHz, Ampl <3 Vpp -55 dBc DC ~ 1 MHz, Ampl> 3 Vpp -45 dBc 1MHz ~ 5 MHz, Ampl> 3 Vpp -30 dBc 5MHz ~ 80 MHz, Ampl> 3 Vpp
|
|
Total Harmonic Distortion |
<0,2% +0,1 mVrms
DC bis 20 kHz |
|
Unechte(nicht-harmonischen) (5) |
-60 DBc DC ~ 1 MHz
-50 DBc 1MHz ~ 20MHz
-50 DBc + 6 dBc / Oktave1MHz ~ 80MHz |
|
Phasenrauschen |
< -65dBc typischen 10MHz, 30 kHz-Band < -47dBc typischen 80MHz, 30 kHz-Band
|
|
Rechtecksignal Eigenschaften |
|
Rise / Fall Time |
<8 ns(3) |
|
Overshoot |
<5% |
|
Asymmetrie |
1% der Zeit ein ns |
|
Variable Duty Cycle |
20,0% auf 80,0% ¿ 25 MHz 40,0% auf 60,0% 25 ~ 50MHz 50,0% (fest) 50 ~ 80MHz
|
|
Jitter |
0,01% 525 ps <2 MHz
0,1% +75 ps > 2 MHz |
|
Ramp Eigenschaften |
|
Linearität |
< 0,1% der Spitzenleistung |
|
Variable Symmetry |
0% bis 100% |
|
Pulscharakteristika |
|
Zeit |
20ns ~ 2000er |
|
Pulse Width |
8ns ~ 1999.9s
Mindest-Impulsbreite:
8ns wenn FREQ ¿ 50MHz
5% der Dauer der Einstellung, wenn FREQ ¿ 6.5MHz
Auflösung:
1 ns, wenn FREQ ¿ 50MHz
1% der Einstellung Zeitraum, wenn FREQ ¿ 6.5MHz |
|
Overshoot |
<5% |
|
Jitter |
100 ppm 50 ps |
|
AM Modulation |
|
Trägersignale |
Sinus, Rechteck, Dreieck, Rampe, Puls, Arb |
|
Stetiger Waveforms |
Sinus, Rechteck, Dreieck, Up / Dn Ramp |
|
Modulationsfrequenz |
2 mHz bis 20 kHz |
|
Tiefe |
0% bis 120,0% |
|
Quelle |
Interne / Externe |
|
FM-Modulation |
|
Trägersignale |
Sinus, Rechteck, Dreieck, Rampe |
|
Stetiger Waveforms |
Sinus, Rechteck, Dreieck, Up / Dn Ramp |
|
Modulationsfrequenz |
2 mHz bis 20 kHz |
|
Peak-Abweichung |
DC bis 80 MHz |
DC bis 50 MHz |
|
Quelle |
Interne / Externe |
|
PWM |
|
Trägersignale |
Quadrat |
|
Stetiger Waveforms |
Sinus, Rechteck, Dreieck, Up / Dn Ramp |
|
Modulationsfrequenz |
2 mHz bis 20 kHz |
|
Abweichung |
0% ~ 100.0% of pulse width |
|
Source |
Internal / External |
|
FSK |
|
Carrier Waveforms |
Sine, Square, Triangle, Ramp, Pulse |
|
Modulating Waveforms |
50% duty cycle square |
|
Internal Rate |
2 mHz to 100 kHz |
|
Frequency Range |
DC to 80 MHz |
DC to 50 MHz |
|
Source |
Internal / External |
|
SWEEP |
|
Waveforms |
Sine, Square, Triangle, Arb |
|
Type |
Linear or Logarithmic |
|
Direction |
Up or Down |
|
Start F / Stop FREQ |
100 uHz to 80 MHz |
100 uHz to 50 MHz |
|
Sweep Time |
1 ms to 500 s |
|
Trigger |
Single, External, Internal |
|
Marker |
Falling edge of Mark signal
(Programmable frequency) |
|
Source |
Internal / External |
|
BURST |
|
Waveforms |
Sine, Square, Triangle, Ramp |
|
Frequency |
1 uHz to 80 MHz(4) |
1 uHz to 50 MHz(4) |
|
Burst Count |
1 to 1000000 cycles or Infinite |
|
Start / Stop Phase |
-360.0°to +360.0° |
|
Internal Period |
1 ms to 500 s |
|
Gate Source |
External Trigger |
|
Trigger Source |
Single, External or Internal Rate |
|
Trigger Delay |
N-Cycle, Infinite: 0s to 85 s |
|
External Modulation Input |
|
Type |
for AM, FM, Sweep, PWM |
|
Voltage Range |
± 5V full scale |
|
Input Impedance |
10kO |
|
Frequency |
DC to 20 kHz |
|
External Trigger Input |
|
Type |
for FSK, Burst, Sweep |
|
Input Level |
TTL Compatible |
|
Slope |
Rising or falling(selectable) |
|
Pulse Width |
> 100 ns |
|
Input Impedance |
10kO,DC coupled |
|
Latency |
Sweep |
< 10 us (typical) |
|
Burst |
< 100 ns (typical) |
|
Jitter |
Sweep |
2.5 us |
|
Burst |
1 ns; except pulse,300 ps |
|
Modulation Output |
|
Type |
for AM, FM, Sweep, PWM |
|
Amplitude |
Range |
¿1Vpp |
|
Impedance |
> 10kO typical (fixed) |
|
Trigger Output |
|
Type |
for Burst, Sweep |
|
Level |
TTL Compatible into 50O |
|
Pulse Width |
> 450 ns |
|
Maximum Rate |
1 MHz |
|
Fan-out |
¿4 TTL load |
|
Impedance |
50O typical |
|
Marker Output |
|
Type |
for ARB, Sweep |
|
Level |
TTL Compatible into 50O |
|
Fan-out |
¿4 TTL load |
|
Impedance |
50O typical |
|
Store/Recall |
10 Groups of Setting Memories |
|
Interface |
GPIB, RS232, USB |
|
Display |
4.3 inch TFT LCD
480 × 3 (RGB) × 272 |
|
System Characteristics |
|
Configuration Times
(typical) |
Function Change:
Standard---->102ms
Pulse-------->660ms
Built-In Arb- >240ms
Frequency Change: 24ms
Amplitude Change: 50ms
Offset Change: 50ms
Select User Arb: < 2s for 1M points
Modulation Change: < 200ms |
|
Arb Download Times
(typical) |
Binary Code |
ASCII Code |
|
GPIB / RS-232 (115 Kbps) |
USB(Device) |
USB(Host) |
|
1M points |
189 Sec |
34 Sec |
70 Sec |
|
512K points |
95 Sec |
18Sec |
35 Sec |
|
256K points |
49 Sec |
9 Sec |
18 Sec |
|
64K points |
16 Sec |
3 Sec |
6 Sec |
|
16K points |
7 Sec |
830mS |
1340 mS |
|
8K points |
6 Sec |
490mS |
780mS |
|
4K points |
6 Sec |
365mS |
520 mS |
|
2K points |
5 Sec |
300mS |
390 mS |
|
General Specifications |
|
Power Source |
AC100~240V , 50~60Hz |
|
Power Consumption |
65 VA |
|
Operating Environment |
Temperature to satisfy the specification : 18 ~ 28°C
Operating temperature : 0 ~ 40°C
Relative Humidity:
= 80%, 0 ~ 40°C
= 70%, 35 ~ 40°C
Installation category: CAT ¿ |
|
Operating Altitude |
2000 meters |
|
Pollution Degree |
IEC 61010 Degree 2, Indoor Use |
|
Storage Temperature |
-10 ~ 70°C, Humidity: =70% |
|
Dimensions (WxHxD) |
Bench Top : 265 (W) x 107 (H) x 374 (D) |
|
Weight |
Approx. 4kg |
|
Safety Designed to |
EN61010-1 |
|
EMC Tested to |
EN 55011, IEC-61326-1 |
|
Accessories |
GTL-110× 1
Instruction Manual×1
Power cord×1 |
|
(1). A total of ten waveforms can be stored.(Every waveform can composed of 1M points maximum.)
(2). Add 1/10th of output amplitude and offset
specification per °C for operation outside of 0°C to 28°C range (1-year
specification).
(3). Edge time decreased at higher frequency.
(4). Sine and square waveforms above 25 MHz are allowed only with an "Infinite" count.
(5). Harmonic distortion and Spurious noise at low amplitudes is limited by a -70 dBm floor. |